3D Printer. Press question mark to learn the rest of the keyboard shortcuts.

This resin is ideal for printing beautiful designs like miniatures and props. Unapproved am used Filament printing where I can adjust the infill and save on plastic for parts that do not need to be solid, but I can figure out how to do it with the Elegoo mars printer and the Chitubox slicing software. Completely levelled on numerous occasions.

But then if you just want to stay all to yourself and not push any boundaries then I suppose what you offer in your comment is the way to go. Are you sure the bed is leveled correctly? Unboxing and testing review by Tessa Nescihttps://www.thingiverse.com/sparkyface5, https://3dwithus.com/elegoo-mars-pro-sla-resin-3d-printer, Elegoo_Mars_Pro_Resin_3D_Printer_Review_-_Unboxing_and_Testing_430.jpg. I've read some people say this should be 60 seconds however I haven't tested that yet. Straight out the box after leveling the build plate (with no grinding) I tried the rook print and booooom grind grind grind after submerging into the resin tank. Forum adverts like this one are shown to any user who is not logged in.

Then there’s the layer lines caused by alignment shifts.

Is this an issue in ChituBox, My USB stick, or the printer? Thats just plain wrong. I should tell you I've replaced my FEP with the Eleggo brand replacement and I always level the build plate according to the Elegoo manual.

Here are all the settings I have as default in chitubox. I increased the first layers time and things were better. Has anyone come across this before? You need enough base plate area and adhesion to hold the print on the base plate, that’s where the higher base exposure time comes in. The only mod I’d consider is a little scuff of the base plate with some 80 grit to help the adhesion. https://3dwithus.com/elegoo-mars-pro-sla-resin-3d-printer, Elegoo_Mars_Pro_Resin_3D_Printer_Review_-_Unboxing_and_Testing_430.jpg, submerge print in glas of water and let sit in the sun for a couple of hours (no lid; aluminium foil on bottom). I obviously can't compare it to the normal resin, as I've never used it, but I seem to get good results.

Mars Pro also comes with a Myminifactory Membership Card, which gives you the privilege to millions of curated 3D objects to start your first printing on Mars Pro. Mammoth Tank Model From Command & Conquer printed in resin. Just about finished by 44" Eagle from Space:1999. I've been printing on my Mars for about 2 months and I'm no expert but initially I had great success printing 100% of my models. "Companies that thrive in the global economy are not usually the ones that work in a vacuum nor support only themselves." Last Post: October 6, 2019 . Has anyone tried and had any success using "Mean Green" cleaning fluid? This group is all about ELEGOO Mars/Mars Pro/Mars 2/Mars 2 Pro/Mars C resin-based printer. I would also be really interested in this. Good luck! Solved just level the bed to the screen with paper and then print, Let it level itself ( it will push the plate in the housing since its spring loaded), after its home and resting on the paper, tighten the bolts on the build plate. It's a cheap 3D printer made by a company that makes lots of different products and sometimes that shows. MDSW. I discovered that the neck join from middle of support to the ball connecter was to thin. Hands on with resin 3D printers: We put the Elegoo Mars, Mars Pro, and Zortrax Inspire to the test. I scaled it down 6% from the original stl files. Here is a long read plus a lot of images, and some tips & tricks!https://3dwithus.com/elegoo-mars-pro-sla-resin-3d-printer I have had great success with most of my models, but I want to try printing something hollow.

I know PrusaSlicer supports lots of FDM printers, I'm hoping the same will happen for SLA printers. Stop the ads. It is time consuming but I throw a lot less away than I used to. didnt send them all first time - here are the rest!

Having a product that can have custom support for printers and be even more customization and supported by 3d people of all kinds makes you a force to be reckoned with.

I've been printing on my Mars for about 2 months and I'm no expert but initially I had great success printing 100% of my models. Straight out the box after leveling the build plate (with no grinding) I tried the rook print and booooom grind grind grind after submerging into the resin tank. Prints coming out reversed on new Mars printer by Bloozrider . If no-one has tried, I will give it a go and let you all know. Forum contains no unread posts Hey, I want to buy one of these 3d printers but I don’t know which one I’m interested in elegoo mars because has a great aligned screw directly inserted to the motor, but I don’t like the linear guide system. Despite the advertising wording, the print bed can be …

About 3 weeks ago I began experiencing print failures where the support rafts were being printed on the FEP. Mark all read, Topic Icons: Anyone else using Elegoo's water washable resin? Sticky

I loaded up the file in ChituBox, and lo and behold: ChituBox showed the exact same issue. I'm guessing that needs to be done so it keeps the home position after it's turned off........not that its storing that position for me by the looks of it. I've been printing on my Mars for about 2 months and I'm no expert but initially I had great success printing 100% of my models. You don’t need lube of any kind in the FEP, tape on the screen or any other random mods. If your layer height is at 0.05 then this works fine for most resins but if you change the resolution then you need to increase or decrease accordingly as smaller layers need less exposure time. I have had great success with most of my models, but I want to try printing something hollow. I have an unknown error that recently occurred.