Click on "Add" to configure a time restriction profile using the appropriate devices MAC address. 6-20 seconds..............Performs the software equivalent to the Restore Defaults function in the gateway software; this is the actual Factory Reset you're probably looking for. The device plugged into the red WAN port will not have connectivity, however.

Sonic Speed Test AC power adapter specifications: 100VAC to 240VAC @ 50/60Hz DC voltage: 12V, 1.5A. Click Apply/Save at the bottom of the page. • WPS Button The WPS button triggers WPS (Wi-FiProtected Setup™) mode. For those of you that are technically inclined, you can ping or trace route to remote hosts to test connectivity.

The modem interface can be accessed though a browser by surfing to http://192.168.42.1/admin. On the Wireless-- Advanced settings page, make the following changes: 7. Refer to the table below for an explanation of indicator behavior.

As much as it's a pain, get the router out of the loop and see if you have the problem with just one computer attached directly to the Cable or DSL modem. Accessing the router’s management interface, This page tells you basic information about the router. Enter 50.0.1.1 as the primary DNS server, and 50.0.2.2 as the secondary DNS server. Note: For SR516ac models, status is shown for both wireless bands in the Test your Wireless Connection row. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. However, if you modify "Internal Port Start", then "Internal Port End" will be set to the same value as "Internal Port Start". Your modem is capable of testing your DSL connection. Open an Internet browser on your computer and connect to the modem by typing 192.168.1.1 in the address bar.

If wireless settings are all you need to configure, the Quick Start guides will provide all the instructions you need. If you would like to bridge the modem yourself, here are the following instructions: If you need to unbridge the modem, the easiest and most direct way is to perform a factory reset. This page allows you to add a time of day restriction to a given LAN device connected to the Router. https://help.ncf.ca/index.php?title=Changing_WiFi_Channels_on_SmartRG_modems&oldid=6561, Password: Your DSL password   (Default is, Wireless channels shouldn't have to be changed often (more than once every 6-12 months). A maximum 96 entries can be configured. Check the box marked "Remove" for all existing WAN service types listed, Select the appropriate service type, either ATM or PTM, and click "Next", Under "WAN Service Configuration", select "Bridging" and click "Next", At the "WAN Setup - Summary" page, click "Apply/Save". Three legs of the data path are included in the available tests: LAN connectivity, DSL connectivity and Internet connectivity tests. Enter the IP address of the device that you wish to trace. This page was last edited on 13 February 2019, at 11:18.

• 1 x RJ12 port (DSL) The grey RJ12 port labeled DSL is specifically intended for connection to an internet provider via a DSL (Digital Subscriber Line) service. Normally, it is set to the same value as "External Port End". If a test displays a fail status, click "Rerun Diagnostic Tests" at the bottom of this page to make sure the fail status is consistent. The problem is I have no idea how to do it. Customers using a SmartRG SR516ac modem on Fusion DSL need not worry about accidentally plugging a device into the red WAN port; unlike a Pace 5268AC, this does not affect surf. I have a WiFi extender, so I would like to turn on WPS. In this section, you can run line performance tests. Each list can include up to 100 addresses. Consult: DSL Rates; Before you start configuring the SmartRG SR505n, there are 4 things to check: … You will need to be connected to the router, either wirelessly or via a direct Ethernet connection. Setup Guides & Temperature: 32° to 104° F (0° to 40° C) Humidity: 5% to 95%, non-condensing Altitude: -197’ – 6,000’ MSL.

DSL password (Default is password, if you reset modem). Modem Lights ON But No Internet – HELP [STEPS TO RESOLVE] Posted at 20/06/2016 12:01pm It’s always an unexpected situation when your modem lights are on but you cannot make a fricking connection to the internet, seriously the most painful situation you’re in right now. Use only the power supply provided with the gateway – use of a different power supply can cause damage to the gateway. You can also ping a host or trace a connection.

Click on “Wireless” in the left navigation bar. This can be useful for testing out customer issues where they are unable to reach a specific web site over their Sonic connection, or they are unable to surf on any device despite us being able to ping and access their modem's interface. Not recommended. I understand. If the gateway has NOT communicated with Sonic, or if it has not communicated with Sonic since a factory reset has been performed, the default username and password will be admin/admin). The SR526ac is a CPE gateway for fiber and single-line DSL installations. Select an application from the drop-down list, or create your own customer application name and configure the appropriate trigger and open port settings. On this page, you can use the Trace Route utility to trace a connection. Dong Ngo/CNET You may have noticed that your router and modem have, like, a ton of constantly blinking lights on them. Some applications such as games, video conferencing, remote access applications and others require that specific ports in the Router's firewall be opened for access by the remote parties. The Broadband Router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer. The reset button on the back of the unit has three functions: Less than 6 seconds.......Performs a modem reset that is equivalent to the Reboot function in the gateway software. The results will take a few moments (up to 15 seconds) to appear. Share a review on Yelp The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'. SmartRG Modem LAN Ports in Yellow; Back of SmartRG SR505n Back of SmartRG SR506n Back of SmartRG SR516ac 2. It is in the format of Sonic-XXXX for the 2.4GHz frequency and Sonic-XXXX-5G for the 5GHz frequency, where XXXX = a random 4 digit number. This is usually available from the router manufacturer's … Expect a 1-3 second delay before the WiFi LEDs turns on.Repeat this step to deactivate the WiFi radios. And, as Service Providers have come to expect, comprehensive remote management is enabled by SmartRG’s industry-leading TR-069 engine. Message Of The Day • 1 x DC Power Input Jack Use only the power supply included with the gateway.

Isolate Clients: Click to prevent client PCs from communicating with one another.